sequence

da40ng.checklist.after_start

Zod-validiert · zuletzt aktualisiert 10.8.2026, 16:08:46

Gespeichert

{
  "id": "da40ng.checklist.after_start",
  "kind": "checklist",
  "title": "After Start Checklist",
  "source_ref": "THB DA40 CHL, Expanded Checklist, Rev 20, Effective 16 March 2026",
  "notes": [],
  "steps": [
    {
      "element": "avionic_master",
      "callout": "Avionic master — ON",
      "target_state": "ON",
      "changes": [],
      "detail": []
    },
    {
      "element": "idle_rpm",
      "callout": "Idle RPM — CHECKED",
      "target_state": "CHECKED",
      "changes": [],
      "detail": [
        "Idle RPM — 710 +/- 30 RPM"
      ]
    },
    {
      "element": "pitot_heat",
      "callout": "Pitot heat — CHECKED / OFF",
      "target_state": "CHECKED / OFF",
      "changes": [],
      "detail": [
        "Pitot heat — on",
        "PITOT HT OFF annunciation — off",
        "Ammeter — check current rising",
        "Pitot heat — off",
        "Ammeter — check current decreasing",
        "PITOT HT OFF annunciation — on"
      ]
    },
    {
      "element": "pfd_mfd",
      "callout": "PFD / MFD — NORMAL MODE",
      "target_state": "NORMAL MODE",
      "changes": [],
      "detail": []
    },
    {
      "element": "altimeters",
      "callout": "Altimeters — SET AND COMPARED",
      "target_state": "SET AND COMPARED",
      "changes": [],
      "detail": [
        "QNH on PFD (baro selector) — set",
        "QNH on STBY instrument — set",
        "Altimeter reading — compare with the airport elevation",
        "Tolerance — within 60 ft from airport elevation"
      ]
    },
    {
      "element": "pfd_settings",
      "callout": "PFD — SET",
      "target_state": "SET",
      "changes": [],
      "detail": [
        "Settings according table end of this CHL",
        "STBY attitude indicator checked and adjusted"
      ]
    },
    {
      "element": "com_gns_nav",
      "callout": "COM / GNS / NAV — ON",
      "target_state": "ON",
      "changes": [],
      "detail": [
        "COM 1 — primary freq. / as req.",
        "COM 2 — 121.5 / as req.",
        "GNS — direct to or flight plan as required. If GNS not used, select CDI on NAV 1 or NAV 2 with RWY heading. Wording: \"GNS not used, CDI green, RWY heading set\"",
        "NAV — not required in Phase 1 + 2",
        "ALT preselect — set",
        "XPDR — set squawk, check GND"
      ]
    },
    {
      "element": "mfd_settings",
      "callout": "MFD — SET",
      "target_state": "SET",
      "changes": [],
      "detail": [
        "Settings according table end of this CHL"
      ]
    },
    {
      "element": "instrument_flood_lights",
      "callout": "Instrument / Flood lights — AS REQUIRED",
      "target_state": "AS REQUIRED",
      "changes": [],
      "detail": []
    },
    {
      "element": "flaps",
      "callout": "Flaps — SET FOR T/O",
      "target_state": "SET FOR T/O",
      "changes": [],
      "detail": [
        "T/O position — set"
      ]
    },
    {
      "element": "elevator_trim",
      "callout": "Elevator trim — SET FOR T/O",
      "target_state": "SET FOR T/O",
      "changes": [],
      "detail": [
        "T/O position — set"
      ]
    },
    {
      "element": "engine_system_page",
      "callout": "Engine / System page — CHECKED / GREEN",
      "target_state": "CHECKED / GREEN",
      "changes": [],
      "detail": [
        "Max 50% power if engine temperature below green range"
      ]
    },
    {
      "element": "departure_briefing",
      "callout": "Departure Briefing — COMPLETED",
      "target_state": "COMPLETED",
      "changes": [],
      "detail": [
        "Departure Briefing acc. SOP 20.2",
        "Set CRS selector, HDG bug and ALT preselect",
        "Review emergency strategy, threats and mitigations"
      ]
    }
  ]
}

⌘/Ctrl + S oder Enter · 3'719 Zeichen